Mastering Plumbing Fundamentals When You Install a Bathtub
Mastering Plumbing Fundamentals When You Install a Bathtub
Blog Article
The content listed below relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is highly enlightening. You should look it over.
Installing a bath tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, as well as often, tiling abilities. Replacing an old bathtub with a new one is also a moderately tough task. If the old tub is conveniently accessible, the project can relocate quickly; if you need to open a wall to eliminate the old tub and place the brand-new bath tub, the task is much harder. In either situation, the project is within a home handyman's skills, although you will need an assistant to move out the old bathtub as well as set in the new one. Ensure you have actually certified yourself for the job and also fit trying it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to consider employing one before you begin. Chances are you might need a specialist plumber to make tube links.
This short article will certainly help you install a new bathtub in your restroom if you have currently bought a brand-new tub and also don't need to alter the setup of your previous water supply pipes.
Your devices and also material checklist must consist of the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, after that the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly troublesome as a result of the restricted accessibility that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the staying water that will originate from the pipelines. Once the supply pipelines have been removed, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this process. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers remain in place in between the faucet and the sink. Secure the tap in position with the producer given backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal faucet connectors. The former kind should be connected to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the called for setting. The wood boards are handy in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the tub till the spirit level reads degree.
To install taps, fit all-time low of the furthest adaptable tap connector to the ideal supply pipeline by making a compression join; after that do the very same for the various other faucet.
Activate the supply of water as well as examine all joints as well as brand-new pipework for leakages and tighten them if needed. Fill up the tub and additionally examine the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, fix the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bath tub ought to wait until the bath tub has been utilized a minimum of once as this will resolve it right into its final setting.
Preparing for the Setup
First of all, the sustaining structure provided with the bathroom must be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the faucets system to avoid pressure on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two faucets making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its final position.
Tiling Around the Bath tub
In the area where the bathroom satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to break an inflexible seal, creating the water to pass through the wall surface between the bathroom and also the tiling, causing complications with moisture as well as possible leaks to the ceiling below.
You can select from a range of coloured sealants to assimilate your components as well as installations. They are offered in tubes as well as cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly load the tub with water before sealing, to enable the motion experienced when the tub remains in usage. The sealer can break fairly early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently available on the market. It is advisable to fit the floor tiles making use of water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about How to Install a Bathtub Yourself? Leave a comment down the page. We would be glad to know your ideas about this content. Hoping that you come back again before long. For those who liked our post if you please make sure you remember to pass it around. Kudos for your time. Visit us again soon.
Secure efficient service. Report this page